Omron Programmable Terminals NT31 NT31C Bedienungsanleitung Seite 173
- Seite / 296
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6-7SectionSetting Conditions for Communications with Host by Using Memory Switches
163
6-7-4 Setting the NT Link (1:N) Method (Standard/High-speed)
Set the communication conditions for the NT link (1:N) method at serial port A or
serial port B by following the operation from the System Menu shown below.
The communications speed determines whether the 1:N NT Link is standard or
high-speed.
Standard: Standard 1:N NT Link
High-speed: High-speed 1:N NT Link
Select Maintenance Mode.
Select Memory Switch.
Display the fourth memory switch screen by
pressing the [↓] (next screen) or [↑] (previous
screen) touch switch.
Press the touch switch corresponding to the
port at which the NT link (1:N) method (stan-
dard or high-speed) is to be set (Comm. A
Method or Comm. B Method) to display the
setting option NT Link (1:N).
The setting option changes each time the
touch switch is pressed.
In this example, serial port A is used.
Ver 3.10
- Setup Manual 1
- NT31and NT31C 2
- Programmable Terminals 2
- OMRON Product References 4
- Visual Aids 4
- TABLE OF CONTENTS 6
- About this Manual: 8
- Related Manuals: 9
- PRECAUTIONS 10
- 2 General Precautions 11
- 3 Safety Precautions 11
- 1 Intended Audience 11
- 3Safety Precautions 12
- SECTION 1 13
- Production Control (3) 14
- % achieved 14
- Electroplating control 14
- 1-2-1 Features 16
- 1-2-6 Displays 23
- Mark Image data Library data 24
- Image/library 27
- 1-3 System Configuration 28
- 1-3-2 Connecting to the Host 29
- 1-4-2 Host Link 30
- 1-4-3 NT Link 30
- 1-5-1 Memory Link 32
- 1-6 Before Operating 34
- 1-6SectionBefore Operating 35
- SECTION 2 36
- Preparing for Connection 36
- Front View 40
- Rear View 41
- SECTION 3 42
- 3-1 Installation 43
- 3-1-3 Power Supply Connection 44
- 3-1-4 Grounding 45
- Serial port A 46
- (RS-232C, 9-pin) 46
- 3-3 Connecting a Printer 47
- 3-4-1 Connection Method 48
- 3-4-3 Data Format 49
- 3-5-1 Installation Method 51
- 3-5-2 Method of Use 51
- Setting of SW1-4 not relevant 55
- Setting of SW2-3 not relevant 55
- Setting of SW2-4 not relevant 55
- 3-6-1 Installation Method 59
- 3-6-2 Method of Use 59
- SW2-3 ON: Bank 1 60
- OFF: Bank 0 60
- SECTION 4 64
- 4-1-1 Host Types and Settings 65
- CS1W-CN118 Connecting Cable 66
- Setting the Front Switches 68
- CQM1H CPUs, SRM1 73
- PROGRAMMABLE CONTROLLER 78
- Set this to RS-232C 82
- Set SW3 to use NT link 82
- (ON, right side) 82
- DIP switch setting (SW3) 82
- Setup effective 84
- Shielding wire 92
- ⇔25-pin, 2 m) 94
- ⇔9-pin, 2 m) 94
- Serial Port B 95
- SECTION 5 96
- NT-AL001 99
- Functional 100
- ⇔ 25-pin, 2 m) 101
- ⇔ 25-pin, 5 m) 101
- (marked 106
- in the figure above) only 106
- in the figure above) 107
- Fork type 110
- 6.2 mm or less 110
- Round type 110
- RS-422A cable 111
- (max. 500 m) 111
- 5-2-1 Host Types and Settings 112
- RS-422A Adapter to connect 113
- LocalHost 115
- Setting the Rear Switches 116
- I/O port selector switch 119
- 4 WIRE 126
- PRINTER PORT B 136
- SECTION 6 141
- System Menu Operation 141
- 6-2 Starting the NT31/NT31C 144
- Transmit Mode 145
- Maintenance Mode 145
- Expansion Mode 145
- 6-3-2 Menu Tree 147
- RUN mode 148
- Press any two of the four 148
- Ver 3.10 149
- 6-4 Memory Initialization 150
- 6-5-4 Clearing Screen Data 164
- Using Memory Switches 167
- 6-8 Starting Operation 178
- 6-9 System Settings 178
- 6-9SectionSystem Settings 179
- 6-11 System Maintenance 201
- 6-11SectionSystem Maintenance 202
- 6-11-6 Checking Screen Data 212
- 6-11-7 Device Check 215
- 6-11-8 Checking Interfaces 225
- 6-12-1 Usable Systems 231
- 6-12-2 Connection Method 233
- 6-12-3 Method of Use 234
- Mode selection keys 235
- Mode lock key 235
- 6-13 Device Monitor Function 237
- 6-13-1 Compatible Systems 238
- 6-13-2 Connection Method 238
- 6-13-3 Method of Use 239
- 6-14 Version Display 240
- SECTION 7 241
- 7-1 Troubleshooting 242
- 7-1SectionTroubleshooting 243
- 7-3-1 Replacing the Battery 254
- 7-4 Inspection and Cleaning 255
- Appendix A 257
- Performance Specifications 258
- Programming Environment 259
- Special Features 259
- Appendix ASpecifications 260
- Communications Specifications 261
- For a Bar Code Reader 263
- Appendix B 264
- Mounting Dimensions 265
- Appendix BDimensions 266
- NT–AL001-E 267
- Removal from a DIN Rail 268
- Specifications 269
- Pin Arrangement 271
- Block Diagram 272
- Appendix D 273
- Appendix E 274
- Soldering 275
- Hood Assembly 275
- Appendix F 276
- Appendix G 277
- Appendix H 278
- Appendix I 279
- Appendix J 281
- Appendix JModel List 282
- Cables with Connectors 285
- Connection Cable 285
- Applicable Connectors 285
- Printer Cable 286
- Appendix K 287
- Memory Unit ... NT-MF261 288
- View angle, 248 292
- Warning label, 30 292
- Waterproofed, 4 292
- Weight, 247 292
- Revision History 293
- Authorized Distributor: 295
Verwandte Produkte und Handbücher für Hardware Omron Programmable Terminals NT31 NT31C
Hardware Omron E7 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Hardware Omron CQM1H-CLK21 Bedienungsanleitung
(401 Seiten)
(401 Seiten)
Hardware Omron DR 170 14 Bedienungsanleitung
(67 Seiten)
(67 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern